Suzuki clips, knobs and trim
22 free models for the Samurai, Sidekick and Jimny. The Sidekick parts fit the Geo Tracker twin. Plenty of soft-top and dash parts, few true clips yet.
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your truck, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Most downloaded
Suzuki
Suzuki parts
22 parts-
Center dash vents1995 Suzuki Sidekick, also same-generation Vitara / Geo Tracker; center dash vent louversTight fit by design; ream holes or sand pins. Print both louver-arm sizes and use the better fit. -
-
Soft-top trim rail (fender)First-gen Suzuki Sidekick / Geo Tracker soft top, side trim along the fender; mirror for driver sideHigh infill ABS or similar; large part, cut in slicer and glue sections. -
Door handle pocketJimny JB64 and JB74 -
Fuel flap release handleJimny JB74 -
Hood prop rod clipJimny (fit-checked on a 1999), likely other Suzukis incl. Sidekick/Vitara; holds the hood prop rod under the hood 09403-07311ABS/ASA only, PLA and PETG soften from engine heat. Print on its side with support. -
Dash aux switch panelJimny JB33 and JB43 -
Transfer case shifter bushingSuzuki Sierra / SJ413 / Samurai transfer case shifterStack two if still loose on worn pins. -
Indicator coverSamurai -
Soft-top roof latch hooksSuzuki Vitara Cabrio 1988-95 (Sidekick/Escudo convertible), replaces the red roof-closure hooksPETG or ASA, 0.15 mm layers, 4+ perimeters, with support. -
Door handle retaining clip1993 Geo Tracker (Sidekick twin) door; holds the door handle in placePETG, flat side down, no supports. -
Throttle cable clipJimny (fit-checked on a 1999), may fit other Suzukis; retains the throttle cable in the engine bay 09403-05311ABS/ASA only, PLA and PETG soften from engine heat. Print on its side with support. -
Soft-top roof bar clipSuzuki Samurai soft top; keeps the rear roof support bar off the tailgate, bolts on with the spare-wheel M8 bolts -
Rear bumper guide1989-98 Geo Tracker / Suzuki Sidekick rear plastic bumper, side guidePETG or ABS, 100% infill, no supports. Fusion 360 file included. -
Jack handle clipSJ410 and SJ413, under the driver seat -
Air vent retainer clipSuzuki Jimny JA22W (1995-98 kei), dashboard air vents -
Switch blankSuzuki Sidekick / Geo Tracker dash, fills empty optional-switch holesABS or ASA, no supports. Press fit. -
Hazard light switch1998 Suzuki Jimny dash hazard switchPETG so it can flex to snap in; print on its side with supports. -
Rear door bump stopSuzuki Jimny JB64 / JB74 / JC74 (2018+), rear door rattle stop -
Vent clip2nd gen Jimny -
Mirror anti-sag collarSuzuki Samurai / Sierra / SJ413 side mirrors; clips over the mirror shaftABS/ASA at 100% infill. -
Side marker indicator coverSuzuki Jimny JB43 (2000-2018), fits over the original side marker light (title says FJ/JB53; check fit)ABS, PETG or ASA for UV and weather. Mount with tape, clips or screws.
Nothing for this model yet. Send us one.
Any make
2 partsClips that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011
-
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Suzuki parts free?
Yes. All 22 are free to download from the creator's page. 14 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right clip for my Suzuki?
Match the OEM part number where it's listed (2 of the 22 have one), or pull the old clip and compare it with the preview photos and what each part fits.
What filament should I print trim clips in?
PETG, ASA or nylon. PLA goes soft in a hot cab, so save it for a test fit. Print one, check it against the old clip, then print the rest.
Where do the files come from?
14 from Printables and 8 from MakerWorld. LRDT doesn't host the files; every part links to its creator's page.
Can I add a part?
Yes. Send the link with the form at the bottom of this page. We check the fit and the license, then add it with the creator's name on it.
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.