Land Rover clips, knobs and trim
31 free models for the Defender, Discovery, Range Rover, Series and Freelander. From the Series trucks that started it to the new Defender.
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your truck, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Most downloaded
Land Rover
Land Rover parts
31 parts-
Door trim clipDefender 110, door card panel clipPETG at 0.28mm works; TPU is more durable and survives removal (V2 tuned for TPU) -
Hatch panel clipDiscovery Sport, rear hatch trim panel (likely other panels too)No supports; print the body in a high-temp material (not PLA) and the anti-rattle ring in TPE/TPU -
Fuel door latchDiscovery 2, fuel filler door latchPETG with 1.2mm walls; use a brim, no supports; heat and squish the square tab to lock it -
Side vent cover1995 Defender 90 300Tdi, right-hand drive -
Battery air intake clipRange Rover Evoque L551 -
Brake pipe axle clipBeam-axle Land Rovers roughly 1948 to 2016, holds 3/16 in (4mm) brake pipe to the axle with one cable tieFit is tight; trim the opening slightly if the pipe will not snap in -
Bonnet support rod clipDefender, clip that holds the bonnet prop rod -
Side panel rubber bufferSeries Land Rover, side panel buffer, takes an M8 screw 338553 / 338550Print in TPU or other flexible filament -
Bonnet hinge bushDefender, bonnet hinge 346849 -
-
Tailgate trim panel clipFreelander 1, tailgate trim panelNo supports; works in PLA but a tougher material is recommended -
-
Sill trim rivet pinRange Rover Classic, inner pin for the rivets holding the outer sills (40 per car)Print with the pins standing up -
Fuel door latch clipDiscovery 1, fuel filler door latchUse the V2/V3 version with an M3x25 bolt (and M3 nut); the all-printed V1 broke within a week -
Brake and clutch cylinder coverSeries IIA -
Window regulator clipDefender 90 -
Horn vent infillDefender with the later front wings -
Radiator hose clipDefender TD5, 2.4 and 2.2, also Discovery 2 TD5, radiator shroud / hose clip PYC102200Printed in PETG -
Door card fir tree bracketDefender, factory door cards; replaces the door fixing kit with brackets for standard fir tree fasteners DA4649Print in ABS or ASA to handle cabin heat -
Expanding push rivetDiscovery Sport, engine bay plastic coversPrint in PETG or ABS; a bolt through the centre expands the legs -
Lumbar support knobDiscovery 3 / LR3, seat lumbar adjuster knob -
Headlight clipDiscovery 1, the one that breaks a lot
-
Roof lining fastener clipDefender
-
Door card clip mountsDefender
-
Wiper conversion clipRange Rover L322
-
Wiper blade clipRange Rover
-
Roof rail endRange Rover L322
-
Door latch switch holderRange Rover P38
-
Parcel shelf support bracketRange Rover P38. The creator marks this the old versionTwo parts to join.
-
Seat lever coverDiscovery 4
Nothing for this model yet. Send us one.
Any make
2 partsClips that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011
-
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Land Rover parts free?
Yes. All 31 are free to download from the creator's page. 17 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right clip for my Land Rover?
Match the OEM part number where it's listed (5 of the 31 have one), or pull the old clip and compare it with the preview photos and what each part fits.
What filament should I print trim clips in?
PETG, ASA or nylon. PLA goes soft in a hot cab, so save it for a test fit. Print one, check it against the old clip, then print the rest.
Where do the files come from?
12 from Printables, 10 from MakerWorld and 9 from Thingiverse. LRDT doesn't host the files; every part links to its creator's page.
Can I add a part?
Yes. Send the link with the form at the bottom of this page. We check the fit and the license, then add it with the creator's name on it.
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.