Mercedes Sprinter clips, knobs and trim
27 free models for the T1N, NCV3 and VS30. The van side of overlanding. T1N is 2002 to 2006, NCV3 is 2007 to 2018 and VS30 is 2019 on, and the Dodge and Freightliner Sprinters are the same van.
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your truck, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Most downloaded
Mercedes Sprinter
Mercedes Sprinter parts
27 parts-
Door trim panel clipSprinter rear door card clip (the green OEM style); fits many other vansPETG for heat; needs supports. -
Dash hatch prop and latch2019 on Sprinter dash accessory compartment, holds the lid open for cordsFive pieces glued together; STEP files included. -
Washer fluid tank capW901 to W906 Sprinter (also Vito and Viano W639), 74 mm washer reservoir A1248690172TPU. Scale to 98% for a snug fit. -
Dash vent bladesT1N Dodge and Mercedes Sprinter dash vents, left and right blade setsDark gray ASA is a close color match. H versions take a spring and pin for in-dash repair. -
Mug cup holder2019 on Sprinter dash cup holder, enlarged to take a mug with a handle -
Front door compartment clip1995 to 2006 Sprinter (T1N), re-fastens the front door pocket panel to the doorPLA, 0.2 mm layers; supports only at the base. -
Wheel hub coverT1N Sprinter (W902 to W905) steel wheel center capPETG, 30% infill, 6 walls, supports. -
Door panel clips2007 to 2018 Sprinter (W906), door trim panel -
Interior panel clipsSprinter and VW Crafter cargo area, clips for the rear wall coversPETG with max walls; PLA gets too soft in a hot van. -
Cup holder insert2007 to 2018 Sprinter, replaces the dash cup holder tray; fits a can in a koozie, with pen slotsPETG. Slides in above the tray and snaps down at the front. -
Instrument panel switch coverT1N Sprinter (W903) dash switch blank, with USB pass-through versions A 901 689 3139ABS-GF, 3 walls, 15% gyroid; supports recommended. Needs firm pressure to seat. -
Swivel seat rail end bumper2019 on Sprinter (W907), caps the sharp ends of the seat railsTPU, 0.25 mm layers, printed at 45 degrees. Mirror on X for the other side. -
Dash switch holder2007 to 2018 Sprinter (906) dash switch slot, holds a 16 mm round switchPETG so the clips flex. Glue the switch in; no room for the nut. -
Sun visor hinge mount2006 to 2018 Sprinter (W906), replacement sun visor hinge -
Lower door panel clip2002 to 2006 T1N Sprinter, lower door panelBlack PLA or PETG, flat side down. -
Door cable grommet clip2007 to 2018 Sprinter (W906) and VW Crafter, front door wiring boot clip A0009971151 (grommet)Open design slides over the wires without pulling them. -
Rear door filler cover2019 on Sprinter crew and passenger van, covers the hole behind the rear door panelPETG, dried 6 to 8 hours. Push straight in so the tabs don't snap. -
Upper D-pillar hole cover2019 on Sprinter, large hole in the upper rear D-pillar; version with a 12 mm cable pass-through -
Rear door magnet bumper housing2002 to 2006 T1N Sprinter rear cargo door hold-open magnet 901 740 03 16TPU 64D or 95A. Pause the print to embed the OEM metal parts. -
12V socket adapter2006 to 2018 Sprinter cup holder, swaps the lighter for a 29 mm round USB charger -
Dash switch blankDodge and Mercedes Sprinter dash switch slot, reinforced sides
-
Trim panel clipFits the trim panel holes on a 2013 Sprinter; may need scalingPETG or ABS, 20% infill, no supports.
-
Lower cup holderSprinter knee-height cup holder, 70 mm opening
-
Nalgene cup holder extension2002 to 2006 T1N Sprinter dash cup holder, takes a Nalgene or a large mugDesigned loose; shim with electrical tape.
-
Armrest pad2002 to 2006 T1N Sprinter, replaces the crumbling foam armrest padDrill the printed holes out with a 1/8 in bit; four T20 bolts.
Nothing for this model yet. Send us one.
Any make
2 partsClips that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011
-
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Mercedes Sprinter parts free?
Yes. All 27 are free to download from the creator's page. 16 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right clip for my Mercedes Sprinter?
Match the OEM part number where it's listed (4 of the 27 have one), or pull the old clip and compare it with the preview photos and what each part fits.
What filament should I print trim clips in?
PETG, ASA or nylon. PLA goes soft in a hot cab, so save it for a test fit. Print one, check it against the old clip, then print the rest.
Where do the files come from?
14 from Printables, 7 from Thingiverse and 6 from MakerWorld. LRDT doesn't host the files; every part links to its creator's page.
Can I add a part?
Yes. Send the link with the form at the bottom of this page. We check the fit and the license, then add it with the creator's name on it.
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.