Subaru clips, knobs and trim
34 free models for the Outback, Forester, Crosstrek and Ascent. Hood prop clips and cargo cover parts are the ones that break.
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your truck, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Most downloaded
Subaru
Subaru parts
34 parts-
Fender, bumper and door clipSubaru body clip 909130088 -
Water bottle cup holders2019–2023 Forester -
Roof rack plug2019 Outback roof rack; may fit other years and ForesterPETG, 20% infill, no supports. Add a small rubber band for a watertight seal. -
-
Headlight washer cover2003 to 2009 Outback and Legacy, headlight washer nozzle cover, left and right 86636AG260, 86636AG250 -
Door hole plug2012 to 2018 Forester (made for a 2013), door plug -
Fuse cover clip2011 Outback fuse bay cover and coin drawer -
Interior trim retainer clip2018 to 2023 Crosstrek footrest; most 8 mm retainer holes (replaces Auveco 22705)PETG on its side with supports, 0.16 mm layers. -
Sun visor clip2009 to 2013 Forester (made for a 2010), sun visor retainer hookPETG or ABS, on its side with supports, 4 walls, 40% cubic infill. -
Hood prop rod clip2007 Forester -
Cargo cover support peg2011 Outback (4th gen), right side spring-loaded cargo cover pegPETG or ABS, not PLA. Print on its side with supports for shaft strength. -
Coin box latch clipSubaru coin box 66173AJ000 -
Side skirt pin2004 to 2008 Forester, side skirt mounting pin -
Hood prop rod clip, 10 mm square holeSubaru models that use the 10 x 10 mm square hole for the hood prop clipPETG, fully solid with 4 walls, prints flat with no supports. -
Headlight trim clip2003 to 2008 Forester (SG), headlight trimPrint on its back for strength. V2 is a stronger version. -
Cargo cover stopper2019 to 2021 Forester, tonneau cover stopper, right side 65577AJ00BVHNeeds a 10 mm spring. Print the piece touching the interior in TPU, the rest in ABS. -
Cargo cover catcher2014 to 2018 Forester (SJ), cargo cover catch 94053FJ000, 94053AL100Print inclined with organic supports; snap off the built-in print post after. -
Strut dust cap2012 Outback (Gen IV) 20326AA120 -
Body moulding clip2006 Outback body side moulding; test fit on other modelsPETG at minimum, ASA or ABS better. Multiple walls, 99% infill. Prints without supports. -
Dash switch blank2024 Ascent dash blank insert, for adding a switch or controller -
Floor mat clipFloor mat retainer used across many Subaru models 94099AA270 -
LATCH anchor cover2025 Crosstrek rear seat -
Protector clip2005–2006 Forester rear seat carpet 64356SA010 -
Seat bolt covers2003–2007 Forester -
Shark fin antenna cover2019 Forester and some other years, roof antenna coverASA or other weather-rated filament, flat side down with supports, 3 walls, 15% infill. Seal with paint-safe RTV. -
Seat bolt covers2003–2009 Outback -
Hood prop rod holder2020 Crosstrek, hood prop rod holderPETG for heat resistance. May need a little knife trimming to fit. -
Hood prop clip bracket2003–2007 Forester -
Rear seat back knob2001–2014 Forester and Impreza 64580FA510MU -
Wiper grommets2024–2025 Outback -
Panel clipCrosstrek -
Headlight surround clip1998–2005 Forester -
Rear gate trim2003 to 2007 Forester (SG), rear gate trim panel 94380SA000PETG or better. Use the dowel version and glue the two halves. -
Headlight washer plug2009–2014 Outback
Nothing for this model yet. Send us one.
Any make
2 partsClips that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011
-
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Subaru parts free?
Yes. All 34 are free to download from the creator's page. 24 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right clip for my Subaru?
Match the OEM part number where it's listed (10 of the 34 have one), or pull the old clip and compare it with the preview photos and what each part fits.
What filament should I print trim clips in?
PETG, ASA or nylon. PLA goes soft in a hot cab, so save it for a test fit. Print one, check it against the old clip, then print the rest.
Where do the files come from?
17 from Printables, 16 from MakerWorld and 1 from Thingiverse. LRDT doesn't host the files; every part links to its creator's page.
Can I add a part?
Yes. Send the link with the form at the bottom of this page. We check the fit and the license, then add it with the creator's name on it.
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.