Mitsubishi clips, knobs and trim
34 free models for the Pajero and Montero, Delica, and Triton and L200. Pajero, Montero and Shogun are one chip, and the Delica covers the L300, L400 Space Gear and D:5.
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your truck, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Most downloaded
Mitsubishi
Mitsubishi parts
34 parts-
-
Bumper grommet clipMitsubishi bumper retainer, M5 screw -
Center console armrest latchPajero, center console armrest lid latch -
Interior door screw coverGen 2 Pajero Sport / Montero Sport, interior door panel screw coverASA or ABS, 100% infill, 0.12 mm layers. Mirror for the passenger side. -
Wiper arm pivot coverFirst-gen Montero/Pajero and Dodge Raider, wiper arm pivot nut cover MB623853 -
Armrest clipPajero and Montero MR532555 -
Single cup holderGen 2 Pajero and Montero -
-
Glovebox end stopGen 2 Pajero -
Switch plateDelica -
Folding seat lever knobShogun/Pajero Mk3, 2nd and 3rd row seats -
Sun visor supportGen 2 Pajero/Montero/Shogun (1998), left sun visor support, mirror for rightResin print (Anycubic Flexible Tough worked well), painted to match. -
Side door inner handleDelica L300 and L400, 1986–2004 MR100104521 -
Trim panel clipL200, interlocking trim clip that replaces broken originalsOriginals snap at the stem, so use a strong filament. -
Windshield wiper nut coverGen 2 Pajero -
Dash switch blank coversDelica L400, blank covers for empty dash switch holes -
Window switch frame panel1996-2003 Delica L400 / Space Gear, power window switch frame in the door panelFusion 360 source included. -
Rear A/C buttonPajero, rear air conditioning control -
Pop-out window nutDelica L400, rear pop-out side window latch nutPause mid-print to drop in an M5 nut. -
Tailgate handleL200 -
Curtain slider1986-2004 Delica L300 and L400, window curtain rail sliderPETG or ASA, 100% infill, no supports. Use a clean, degreased sheet. -
Front door lock pull clipDelica L400 / Space Gear, front door lock rod pull, fits left and right MR230269Thicker than stock to stop it breaking again. Fusion 360 source included. -
-
Vacuum hardline clip2000-2006 Gen 3 Montero/Pajero/Shogun, firewall vacuum line clipABS for engine bay heat. PETG probably OK, PLA probably not. -
Square blanking platePajero and Montero interior switch blank -
Roof rail center coverL200, cover for the roof rail tubes -
Spark plug wire retainerMontero Sport -
Rear AC lever cap1995 Delica L400 Space Gear, rear AC panel temperature and vent lever capsABS or PLA, print upright with tree supports, 0.12 mm layers. -
Front bumper vents1995 Delica L400, series 1 -
Seat adjustment handle1993 Pajero -
Seat adjuster handle2015 L200 / Triton, driver seat adjuster handleASA, 0.2 mm layers. A dab of superglue on the pins. -
Curtain clipsDelica -
Rear window bug-screen ventDelica D:5, sliding door window vent insert with mesh, assumes weather shields fittedPETG or ASA for sun and heat. Needs a large bed. -
Alloy wheel center cap, 81mmGen 3 Pajero alloy wheels
Nothing for this model yet. Send us one.
Any make
2 partsClips that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011
-
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Mitsubishi parts free?
Yes. All 34 are free to download from the creator's page. 20 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right clip for my Mitsubishi?
Match the OEM part number where it's listed (5 of the 34 have one), or pull the old clip and compare it with the preview photos and what each part fits.
What filament should I print trim clips in?
PETG, ASA or nylon. PLA goes soft in a hot cab, so save it for a test fit. Print one, check it against the old clip, then print the rest.
Where do the files come from?
27 from Printables, 6 from MakerWorld and 1 from Thingiverse. LRDT doesn't host the files; every part links to its creator's page.
Can I add a part?
Yes. Send the link with the form at the bottom of this page. We check the fit and the license, then add it with the creator's name on it.
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.