Ineos clips, knobs and trim
12 free models for the Grenadier and Quartermaster. A young truck with an active owner community printing the fixes and add-ons the factory missed.
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your truck, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Most downloaded
Ineos
Ineos parts
12 parts-
Cubby box insertIneos Grenadier, insert for the cubby box -
Number plate light shieldIneos Grenadier rear plate lights, cuts glare in the reverse camera; left and right versionsPETG or ABS for UV. 30% infill, no supports; tilt each side 7 degrees so it sits flat. -
Centre console storage trayIneos Grenadier, drops into the centre console as an upper storage layerPLA tested, 30% infill, 4 walls, print upright with supports on the tabs. Needs a 190 x 160 mm bed. -
Cup holder enlargerIneos Grenadier front cup holder, sized so a Yeti mug fits -
Barrier and hanger hole plugIneos Grenadier 13 mm barrier mounting holes; takes an M6 bolt to hang gearPLA Pro, 0.16 mm layers, 50% infill, 4 walls, with support. -
Gridfinity centre console insertIneos Grenadier and Quartermaster centre console; magnetic and non-magnetic versionsPETG for cabin heat, supports on build plate only. -
Roof power outlet coverIneos Grenadier, replacement cover for the factory roof power outletsPrinted in CF nylon for weather; ASA also works. -
Spotlight blanking coverIneos Grenadier front factory spotlights, hides them when bigger driving lights are fittedPETG or ABS, 50% infill or more, outside face down. Fit with a bead of silicone so it can come off. -
Rear vent protectorGrenadier rear vents -
Steel wheel nut coverIneos Grenadier stock steel wheels; short sleeve for use with a nut check, tall withoutASA for exterior use, standard ASA settings. -
-
Rear seat cup holderIneos Grenadier rear footwell between the seats; two cups plus storage, 11 in wideRotate in the slicer so it sits flat.
Nothing for this model yet. Send us one.
Any make
2 partsClips that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011
-
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Ineos parts free?
Yes. All 12 are free to download from the creator's page. 10 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right clip for my Ineos?
Pull the old clip and compare it with the preview photos and what each part fits.
What filament should I print trim clips in?
PETG, ASA or nylon. PLA goes soft in a hot cab, so save it for a test fit. Print one, check it against the old clip, then print the rest.
Where do the files come from?
10 from Printables and 2 from MakerWorld. LRDT doesn't host the files; every part links to its creator's page.
Can I add a part?
Yes. Send the link with the form at the bottom of this page. We check the fit and the license, then add it with the creator's name on it.
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.