Lexus clips, knobs and trim
26 free models for the GX, LX and RX. Lexus uses a lot of Toyota part numbers, so check the Toyota page too: the GX is a 4Runner and Land Cruiser Prado underneath, the LX a Land Cruiser.
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your truck, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Most downloaded
Lexus
Lexus parts
26 parts-
Floor mat clipRX400h floor mat retainer, likely many other Lexus and Toyota modelsPrint on its side with tree supports, 100% infill -
Backup camera mount2006 GX470, holds an aftermarket camera in the factory camera location -
Cup holder insert2010-2022 GX460, center console cup holdersPLA or PETG, 0.2 mm layers, 5-15% infill, large side down with organic supports -
Switch blank with USB port2nd gen RX (tested 2007 RX350), dash switch blank socket; likely other Lexus/Toyota 55539-48020No supports; use a heat resistant material -
-
Headlamp dust coverLX450, LX470, LX570, LX600 headlamp rear cover (tested on LX470); no wire holes -
Headlight washer cover2016-2020 RX F Sport, left headlight washer coverPETG or ASA, not PLA; 3 perimeters, 50% infill -
Dash garnish clipRX350, dash garnish trim clip, replaces weak factory clipsASA or PA for heat, no supports -
Ignition key ring2nd gen RX, ignition cylinder trim ringPrint in white or glow material to let light through -
Backup camera mounting plate2007 RX350, replaces the factory camera bracket to hold an aftermarket camera 86790 -
Center console tray2024 and later GX550, center console trayPETG, 15-25% infill, supports on longest overhangs -
Roof rack slot cover2007 RX350, roof rail slot covers (front, middle and rear pieces)Tight fit; press in with a plastic trim tool -
Third row seat floor plug2006 LX470, 3rd row seat floor anchor cover (likely other years) 72918-60010-A1 -
Roof rack middle coverGX470 roof rack, left and right 63495B / 63496 -
Intake resonator delete plugGX470, keeps the vacuum connection -
Cup holder2003-2009 GX470, center console cup holder; snaps in with printed or factory clipsPETG or ASA for heat, 0.2 mm layers, 4 walls, 15% infill -
Cup holder replacement2008–2015 LX570, replaces the stock cup holderHolds a phone, flashlight and Nalgene-size bottles.
-
Larger cup holderLX470 and 100 Series Land Cruiser
-
Push start blankGX470 dash switch blank
-
Roof rack delete coverGX470, covers the holes after removing the roof rackABS, 100% infill; M8 button heads and sealant.
-
Ash tray switch panelGX470, replaces the dash ash tray drawer with locker switches and USBTest fit on a 2005 GX470.
-
Power antenna gearLX470 power antenna
-
Air ductGX460
Nothing for this model yet. Send us one.
Any make
2 partsClips that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011
-
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Lexus parts free?
Yes. All 26 are free to download from the creator's page. 15 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right clip for my Lexus?
Match the OEM part number where it's listed (4 of the 26 have one), or pull the old clip and compare it with the preview photos and what each part fits.
What filament should I print trim clips in?
PETG, ASA or nylon. PLA goes soft in a hot cab, so save it for a test fit. Print one, check it against the old clip, then print the rest.
Where do the files come from?
13 from Printables, 10 from Thingiverse and 3 from MakerWorld. LRDT doesn't host the files; every part links to its creator's page.
Can I add a part?
Yes. Send the link with the form at the bottom of this page. We check the fit and the license, then add it with the creator's name on it.
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.